CHECK YOUR ADDRESS

SEE IF YOU CAN GET SUPER-FAST INTERNET

Setup Guide


Guide to your first time connecting to our network


These generic settings are usable for most Ethernet compatible routers, and can be used with your Uniti service.

  • Username: username@unitiair
  • Encapsulation PPPoE
  • Authentication Method: CHAP, PAP or Auto
  • Connection Type: Ethernet WAN

While this should be all you need to configure in *most* compatible routers, sometimes there are other settings that may need adjusting.
Uniti Support are happy to speak with you regarding configuration of your hardware, but be aware that this is best effort, and you may be directed to the manufacturer for further assistance.

If you have purchased a router from Uniti directly, a step by step guide on how to configured it can be found below.

Choose your router

Step 1

setup step 1

Download the AmpliFi Wifi app from your respective App Store using the following link:

https://www.amplifi.com/app.html

Connect the PoE cable to the WAN (Blue) port on the AmpliFi

Step 2

setup step 2

Connect the Power Cable to the AmpliFi

Step 3

uniti wallplate
Open the Amplifi Wifi App

Select "Set Up AmpliFi Mesh System"

Step 4

setup step 2

Select "SKIP"

Step 5

setup step 2

Select the AmpliFi Router to begin the setup procedure.

Step 6

uniti wallplate

Set a wireless network name and password of your choice.

NOTE: The name and password are case sensitive, so please ensure you are mindful of capital letters.

Step 7

setup step 2

Select "Skip"
If you wish to set up Remote Access, you will need to contact AmpliFi.

Step 8

setup step 2

Tap on your AmpliFi device to configure your router.

Step 9

setup step 2

Under the “SETTINGS” heading, select "Internet"

Step 10

setup step 2

Select "Network Type" and change to “PPPoE”

Input the credentials provided in your activation email, and hit the tick found at the top right.

That's it, you should now be connected and good to go!

Step 1

setup step 1

In the App store, download the UNMS app
Once installed, open the UNMS app & press ‘+’

Step 2

setup step 2

Select ‘Scan QR Code’

Step 3

setup step 3

Scan the barcode found on the back of your AirCube Router

Step 4

setup step 4

Select the nearby airCube

Step 5

setup step 5

Click Log in

Step 6

setup step 6

On the top menu, click the ‘Network’ button.

Step 7

setup step 7

Click ‘Network Mode’ and change from Bridge to Router.
Then under ‘Interfaces’, click WAN Network

Step 8

setup step 9

Change ‘Mode’ to “PPPoE”, and enter your PPPoE Username and Password found in your activation email and click Done.

Step 9

setup step 10

Click Save/Apply

Step 10

setup step 11

Click Save Changes

Step 11

setup step 12

Wait for the settings to be applied.

Step 12

setup step 13

Internet should say connected or similar.

Step 1

setup step 1

In the App store, download the UNMS app
Once installed, open the UNMS app & wait for the app to locate the router.

Step 2

setup step 2

Select the device from the list & then select ‘Scan QR Code’

Step 3

setup step 3

Scan the barcode found on the back of your AirCube Router

Step 4

setup step 4

The app will go through a series of setup step on your behalf.
Wait while the app logs in to the device

Step 5

setup step 5

The app will run through license agreement

Step 6

setup step 6

The app will reload the device configuartion

Step 7

setup step 7

Select the menu from the top left

Step 8

setup step 8

Select configuration

Step 9

setup step 9

Select "Network Mode" and change to "Router"
Under then WAN heading, select "PPPoE"

Step 10

setup step 10

Input the PPPoE username and password found in your activation email and press apply

Step 11

setup step 11

Wait while the app configures your router and you should be good to go!